SciELO - Scientific Electronic Library Online

 
vol.72Photocatalytic Activity of MOF-derived Cu2O/Cu/C/Ag Porous CompositesComparative Effects of Silver Nanoparticles, Sucrose and Sodium Chloride as Osmotic Solutions for Tomato Slices: Antioxidant Activity, Microbial Quality and Modelling with Polynomial Regression Model author indexsubject indexarticles search
Home Pagealphabetic serial listing  

Services on Demand

Article

Indicators

Related links

  • On index processCited by Google
  • On index processSimilars in Google

Share


South African Journal of Chemistry

On-line version ISSN 1996-840X
Print version ISSN 0379-4350

S.Afr.j.chem. (Online) vol.72  Durban  2019

http://dx.doi.org/10.17159/0379-4350/2019/v72a3 

RESEARCH ARTICLE
doi: https://doi.org/10.17159/0379-4350/2019/v72a3

 

Production and Characterization of Carbon Molecular Sieves from Bituminous Lafia-Obi Nasarawa Coal by Pore Size Modification with Spent Engine Oil

 

 

E. Bala*; O.R. Momoh; B.O.Aderemi; B.J. El-Yakubu

Department of Chemical Engineering, Ahmadu Bello University Zaria, Nigeria

 

 


ABSTRACT


In this work, a carbon molecular sieve (CMS) was produced from a bituminous Lafia-Obi Nasarawa coal. An initial activated carbon (AC) sample was prepared via chemical activation from the coal, from which the CMS samples were then produced through heat treatment processes and carbon deposition from spent engine oil. Spent engine oil was pyrolyzed in order to deposit carbon at the pore mouth of coal-based AC to yield CMS. The effect of reaction temperature and holding time variation on the surface area, micropore pore volume and pore size of CMS was studied. Reaction temperature was varied at 400, 550 and 700 °C while holding time was varied at 30 and 60 min. The Brunauer-Emmett-Teller (BET) method was used to calculate the surface areas, while the Dubinin-Radushkevich (DR) and Horváth-Kawazoe (HK) methods were used to determine the micropore volumes and pore sizes of the AC and CMS, respectively. The CMS sample with the largest BET surface area (5.824 m2 g-1), DR micropore volume (0.172 cm3 g-1) and HK pore size (6.317 A) were obtained at 700 °C reaction temperature and 60 min holding time. In addition to this, a molecular sieving ability test to separate benzene from a mixture of benzene and o-xylene in solution was carried out on the AC and CMS, with the CMS having a selective benzene percentage uptake of 61.36 %.

Keywords: Activated carbon (AC), carbon molecular sieves (CMS), carbon deposition, reaction temperature, holding time.


 

 

1. Introduction

The separation of molecules from mixtures into their various components constitutes a significant cost in industry from an energy and environmental perspective.1 Some very common and important molecular separations in the chemical industry today involve the separation of air, petrochemicals and alcohols by processes requiring large amounts of energy with its attendant environmental pollution implications. Owing to this, there is an increasing interest in the use of adsorbents operating at moderate process conditions to achieve these molecular separations with reduced energy consumption, and minimal negative impact on the environment. CMS are a special type of AC able to discriminate molecules on the basis of their size and shape.2 They are microporous materials, capable of carrying out molecular separations based on the differences in the rates of adsorption of the adsorbate molecules.3 The choice of the raw material constitutes the first important step for CMS production. Generally, certain bituminous coal qualities and coked coconut shells have proven to be suitable raw materials for industrial production.4 CMS can be synthesized from various carbon-containing precursors such as lignocellulosic materials, coals, carbon fibres and pitch by different methods like: (i) pyrolysis (ii) controlled gasification of chars to increase the pore size, (iii) thermal treatment of carbon precursor to modify the pore size, (iv) chemical vapour deposition (CVD) of carbon in the mouth of the pores and, (v) modification of coals by mixing with tars and resins and subsequent carbonization.5 Another approach for narrowing the pore size is by the pyrolysis of an organic precursor previously impregnated in the AC. Alcaftiz-Monge et al.4analyzed this approach and prepared CMS from the co-carbonization of a bituminous coal impregnated with a slurry of coal tar pitch. Bituminous coal, due to its microstructure and surface composition, has been proposed as a precursor for CMS by many researchers.4,6-7 To optimize the preparation process, the modification of the porosity (pore blocking) of the starting AC, the molecular sieving properties of the CMS obtained by this method are analyzed. A report by the World Energy Council8 puts Nigeria's total proven coal reserves at 344 million tons, most of which fall within the rank of bituminous or sub-bituminous. Of the total Nigerian coal deposits, the Lafia-Obi basin has an estimated 21 million tons of bituminous coal reserves.9 This makes it an attractive economically viable precursor for the production of CMS. This study investigates the effect of reaction temperature and holding time variation on the surface parameters of CMS made from bituminous Lafia-Obi Nasarawa coal using spent engine oil as a carbon deposition agent.

 

2. Experimental

The schematic diagram of the experimental setup is shown in Fig. 1. The main component of the system is a stainless steel reactor (23.5 cm internal diameter). The reactor is designed for a batch operation and it is heated within an enclosing electronic tube furnace.

Prior to the carbonization process, a proximate and elemental analysis was carried out on the coal raw material to determine its ranking and the results obtained are presented in Tables 1 and 2. All samples were characterized in terms of surface area, micropore volume and pore size by N2 adsorption at 77 K in a Quantachrome Autosorb Automated Gas Sorption System. The sample was placed inside a tube and a glass bulb was inserted inside the tube. The bulb was inserted by slanting the sample tube almost to a horizontal position. Before an experiment began, the adsorbents were degassed mm Hg) at 393 K. The surface area of the samples was measured based on the BET method. The DR method was applied to calculate the micropore volume, and the pore size was investigated based on the HK method.

 

 

 

 

2.1. Preparation of Activated Carbon (AC)

A size reduction of the raw coal material was carried out to a 2 mm aperture. A100 g coal sample was then weighed and mixed with 400 g of phosphoric acid (H3PO4 85 % v/v), continuously stirred on a constant temperature magnetic stirrer at 80 °C for a period of 3 h to ensure maximum contact and mixing between the acid and sample. The resulting slurry was then placed in an oven to dry at 105 °C for a period of 24 h.10 50 g of the phosphoric acid impregnated coal was packed into a tubular stainless steel vessel (ID 24 mm, L 30 cm) and placed in an electronic furnace. The furnace was heated under nitrogen atmosphere at a flowrate of5Lmin 1 and a heating rate of 6 °C min-1 up to a final temperature of 600 °C, and then held at this temperature for 2 h after which the furnace was switched off and allowed to cool under nitrogen till room temperature. The cooled coal sample was then thoroughly washed in distilled water while constantly monitoring the pH level of the solution until a neutral pH was observed, before being oven-dried at 105 °C for 12 h to eliminate all moisture.11 A BET analysis and molecular sieving ability test to determine the ability of the AC to selectively adsorb benzene over o-xylene from a binary solution of the two was then carried out on the resulting AC sample.

2.2. Preparation of the Carbon Molecular Sieves (CMS)

10 g of AC was weighed and transferred into a beaker contain-ing5gofspent engine oil. The mixture was then rigorously stirred for a period of 30 min to attain homogeneity, placed in a covered vessel and left to stand at room temperature for a period of24h.5goftheengine oil impregnated AC sample was weighed, placed in the tubular stainless steel vessel and heated in the electric furnace under nitrogen atmosphere at a flowrate of 5 L min-1. With the AC sample being heated at a rate of 6°Cmin-1, the temperature of the furnace was raised to 400 °C and kept at this temperature for 30 and 60 min. This experiment was repeated at temperatures of 550 and 700 °C with holding times of 30 and 60 min for all reaction temperatures. The resulting CMS samples were then taken for a BET analysis and molecular sieving ability test to determine their ability to selectively adsorb benzene over o-xylene from a binary solution of the two.

2.3. Molecular Sieve Ability Test for AC and CMS

Benzene and o-xylene solutions of 99.5 % (v/v) purity were used to prepare the standard solutions used in the plotting of the absorbance versus concentration calibration curves to determine equilibrium concentrations. The initial stock solution concentrations of the reagents were determined to be 11.21 M for benzene and 8.25 M for o-xylene. Standard solutions of varying concentrations ranging from 0.1 M to 0.5 M were prepared for both reagents using methanol of 98.5 % (v/v) purity as a solvent. All solutions were then taken for UV spectrophotometry analysis. Methanol 98.5 % (v/v) was added to a solution mixture containing 0.39 mL of 11.25 M benzene and 0.53 mL of 8.25 M o-xylene to make up a total volume mixture of 10 mL. The change in concentrations of benzene and o-xylene in solution were then determined from their respective calibration curves (see Fig. 5). This mixture was divided into two equal parts and poured into two 50 mL beakers, one containing 0.25 g of AC and the other 0.25 g of CMS 700/60 (The CMS sample produced at 700 °C and 60 min holding time). The beakers were then placed in an agitator for 24 h until equilibrium was attained after which 2 mL was drawn from each solution and taken for UV spectrophotometry analysis.

 

3. Results and Discussion

3.1. BET Results for AC

The AC sample had a surface area value of 596.2 m2 g-1,a DR micropore volume of 0.173cm3 g-1 and HK pore size of 9.432 A. The development of porosity in activated carbons made from bituminous coals has been discussed by numerous researchers.1,6,10

3.2. Proximate and Elemental Analysis of Raw Coal Sample

From Table 1 the proximate analysis of the raw coal sample indicates that it has a moisture content of 14.1 %, a fixed carbon of 63.61 %, an ash content of 14.07 % and a volatile matter of 8.22 %. Also, by way of elemental analysis as shown in Table 2, the coal sample has a carbon content of 76.2 %, a hydrogen content of 5.89 %, nitrogen of 2.19 %,with sulphur and oxygen at 5.9 % and 9.82 %, respectively. According to Speight12 the most important parameters used in determining the ranking of coals are the fixed carbon content for the proximate analysis and the percentage carbon content for the elemental analysis. Since both results of the fixed carbon and percentage carbon content are 63.61 % and 76.2 %, respectively, the coal sample used for this study can be ranked as being bituminous, and hence can serve as a suitable precursor for the production of CMS.7

3.3. Effect of Reaction Temperature and Holding Time Variation on Surface Area of CMS

Figure 2 shows the effect of reaction temperature and holding time on the development of the surface area of the various CMS samples. The data in the figure show a progressive increase in surface area values for all CMS samples produced with increasing reaction temperatures and times after an initial drop from that of the AC precursor (see Table 1). This could be as a result of excessive pore mouth blocking by the unpyrolyzed oil and char formed during the pyrolytic decomposition of the spent engine oil molecules embedded within the pore structure.13-14 At both holding times of 30 and 60 min, an increase in surface area was observed as pyrolysis temperature was increased. It can be postulated that with higher pyrolysis temperatures, lighter hydrocarbons are formed to the detriment of residue (char), which in turn escape the pores and get deposited as carbon at the pore mouths and exterior of the CMS pore structure. This in turn leads to some mesopores being converted to micropores, thus enhancing surface area development.15

 

 

An increase in residence time equally led to a corresponding increase in surface areas at all temperatures, due to fact that a longer deposition time is necessary for the complete pyrolytic decomposition and deposition of the spent oil mole-cules.16-17

3.4. Effect of Reaction Temperature and Time Variation on DR Pore Volume of CMS

Reaction temperature and time variation was found to have a significant effect on the DR pore volume of the CMS. During the reaction, a rigorous control of reaction temperature and time is necessary so as to avoid the pore mouth blockage that occurs when excessive carbon is deposited within the pore structure of the CMS.18 In light of this, reaction temperatures were kept at 400,550 and 700 °C, while residence times were varied at 30 and 60 min. This is illustrated in Fig. 3.

 

 

A reduction in the pore volume for all CMS samples from that of the AC sample was observed. It can be proposed that at relatively lower reaction temperatures, the molecules from the oil formed in the vapour phase Are 'pyrolytically' deposited in the interior of the pores and not at the pore mouths, leading to the excessive coke formation within the pores and a lower pore volume (adsorption capacity).15 As reaction temperature and time are increased, an improvement in pore volume can be observed. This could be because as the transition of the spent engine oil molecules from the liquid to gas phase takes place more rapidly, the pyrolytic cracking and deposition takes place more at the pore mouths and exterior of the pore structure, leading to a considerably less amount of coke formation within the pores.13-14 Also with longer holding times, the heat transfer within the oil molecules is more enhanced leading to a more rapid phase change and carbon deposition at pore mouths and the exterior.19

3.5. Effect of Reaction Temperature and Holding Time Variation on HK Pore Size of CMS

The pore size of a CMS is a very important surface characteristic, owing to the fact that it confers upon the CMS the all-important quality of selectivity. It is at this point that the effect that reaction temperature and holding time have on the deposition of carbon on the molecular sieve's surface and thus its pore size modification, come into play.15 From Fig. 4 it can be seen that at all reaction temperatures and times, the values of the pore sizes of all CMS samples steadily decline from that of the AC precursor from which they were made. As is observed, when reaction temperature and time get increased, deposition of carbon from the pyrolytic decomposition of hydrocarbon oil molecules occurs more at the pore mouths and exterior than inside the pore structure, leading to progressive pore size narrowing.

 

 

3.6. Molecular Sieving Ability Test for AC and CMS 700/60

A molecular sieving ability test was carried out on the AC and the CMS sample produced at 700 °C and 60 min deposition time (CMS 700/60), the results of which are presented in Table 3, while Fig. 5 presents the calibration curves for 11.21 M benzene and 8.25 M o-xylene solutions.

When the AC is brought into contact with a 0.44 mol L-1 binary solution of benzene and o-xylene, the percentage uptakes at equilibrium are both relatively high (98.41 and 70.45%, respectively). This is because the AC performs rather poorly in its attempt to selectively adsorb either of the molecules over the other even though a marked drop in concentration can be observed for both molecules. This phenomena can be explained from the point of view that the benzene molecules having a kinetic diameter of 5.85 A20 being smaller than that of o-xylene (diameter 6.8 A),21 was able to penetrate into the pore structure of the AC (HK pore size 9.44 A) with a lot more ease than the larger o-xylene molecule. On the other hand, the CMS 700/60 (HK pore size 6.31 A) performed better in terms of the selective discrimination of the benzene molecules over o-xylene. This is because the larger o-xylene molecules are unable to penetrate in to the CMS pore structure as readily as benzene. At this point it would be pertinent to note that CMS 700/60 does not possess a strictly uniform pore size distribution, meaning its pore structure consists of mesopores and pores with each sub-group having different pore size ranges. This is suggested in the work of Adinata et al.15 who established the heterogeneous pore size distributions of chemically activated coals and CMS even in cases where a significant portion of the distribution falls within the microporous range. This could be the reason why there was a noticeable uptake of o-xylene molecules at equilibrium despite it having a larger kinetic diameter than the pore size of the CMS 700/60 adsorbent.

 

4. Conclusion

A preliminary proximate analysis of the sample returned proximate and elemental analysis values confirming the bituminous nature of the Lafia-Obi Nasarawa coal used in this study. An AC was produced via chemical activation from the coal. The AC had a BET surface area of 596.2 m2 g-1, a DR pore volume of 0.173 m2 g-1 and a HK pore size of 9.432 A. These results classify the AC as a microporous in nature capable of serving as a precursor for the production of CMS. Spent engine oil after undergoing pre-treatment was successfully used as a carbon depositor to achieve pore size modification of the AC to produce CMS under varying temperature and time regimes. The CMS produced designated CMS 700/60 in the text was found to have a BET surface area of 582.4 m2 g-1, DR pore volume of 0.172 m2 g-1 and HK pore size diameter of 6.317 A. A molecular sieving ability test was carried out on AC and CMS 700/60 to test their ability to selectively adsorb benzene over o-xylene in a binary solution mixture. CMS 700/60 was successful to an extent in this regard and owing to its HK pore size (6.31 A) was determined to be a Type 2 carbon molecular sieve.

§ORCID iD

E. Bala: orcid.org/0000-0002-3260-9430

 

References

1 A.A. Lizzao and R.M. Abadi, Production of carbon molecular sieves from Illinois coal, Fuel Pro. Tech, 1993, 34, 97-122.         [ Links ]

2 R.L. Mieville and K.K. Robinson, Carbon Molecular Sieves and other Porous Carbons: Synthesis and Applications, 2015. http://www.megacarbon.conVtechlit/carmolsiv.pdf        [ Links ]

3 M. Mohammadi, A.R. Mohamed and G.D. Najafpour, Production of carbon molecular sieves from palm shell through carbon deposition from methane, Chem. Indus. Chem. Eng. Quat., 2011,17(4), 525-5334. DOI: 10.2298/CICEQ110506038M        [ Links ]

4 J. Alcaniz-Monge, J.P. Marco-Lozar and D. Lozano-Castelló, Mono-lithic carbon molecular sieves from activated bituminous coal impregnated with a slurry of coal tar pitch, Fuel Pro. Tech., 2012, 95, 67-72. DOI: 10.1016/j.fuproc.2011.11.016        [ Links ]

5 D. Lozano-Castello, D. Cazorla-Amorós, A. Linares-Solano, W. Zhu, F. Kapteijn and J.A. Moulijn, Adsorption properties of carbon molecular sieves prepared by a co- carbonization process, Carbon, 2003,43(8), 1643-1651. DOI: 10.1016/j.carbon.2005.01.042        [ Links ]

6. E. David, A. Talaieb, V. Stanciu and A.C. Nicolae, Synthesis of carbon molecular sieves by benzene pyrolysis over microporous carbon materials, Jour. Mat. Pro. Tech., 2004,157-158, 290-296. DOI: 10.1016/j.jmatprotec.2004.09.046        [ Links ]

7 B.Y. Jibril, R.S. Al-Maamari, N. Al-Mandhary, G. Hegde and O. Houache, Effects of feedstock pre-drying on carbonization of KOH-mixed bituminous coal in preparation of activated carbon, Jour. Anal. Appl. Pyrol., 2007, 80, 277-282. DOI: 10.1016/j.jaap.2007.03.003        [ Links ]

8 World Energy Council, World Energy Resources, 2016, 62. https://www.worldenergy.org/wp-content/uploads/2017/03/WEResources_Coal_2016.pdf        [ Links ]

9 Nigeria: Summary of the Coal Industry, 2014. https://www.globalmethane.org/documents/toolsres_coal_over-view_ch24.pdf        [ Links ]

10 D. Cuhadaroglu and A.U. Oznur, Production and characterization of activated carbon from a bituminous coal by chemical activation, Afr. J. Biotech., 2008, 7 (20), 3703-3710.         [ Links ]

11 H. Teng, T. Yeh and Hsu, Preparation of activated carbon from bituminous coal with phosphoric acid activation, Carbon, 1998,36 (9), 1387-1395. http://dx.doi.org/10.1016/S0008-6223(98)00127-4        [ Links ]

12 J.G. Speight, Handbook of Coal Analysis, 2005, Hoboken, John Wiley & Sons Inc., New Jersey.         [ Links ]

13 S.S. Lam, A.D. Russell and H .A. Chase, Pyrolysis using microwave heating: a sustainable process for recycling used car engine oil, Indus. Eng. Chem. Res., 2010,49, 10845-10851. DOI: 10.1021/ie100458f        [ Links ]

14 S.S. Lam, A.D. Russell, C.L. Lee, S.K. Lam and H.A. Chase, Production of hydrogen and light hydrocarbons as a potential fuel from microwave-heated pyrolysis of waste automotive engine oil, Inter. J. Hydro. Energy, 2012, 37, 5011-5021. DOI: 10.1016/j.ijhydene.2011.12.016        [ Links ]

15 D. Adinata, W.M. Daud and M.K. Aroua, Production of carbon molecular sieves from palm shell based activated carbon by pore sizes modification with benzene for methane selective separation, Fuel Proc. Tech., 2007, 88, 599-605. DOI: 10.1016/j.fuproc.2007.01.009,         [ Links ]

16 Y. Changtao, L. Yang, M. Yue, L. Shuyuan, H. Jilai and Q. Dengeke, Influence of retorting conditions on the pyrolysis of yaojie oil shale, Oil Shale, 2014, 31(1), 66-78. DOI: 10.3176/oil.2014.1.07        [ Links ]

17 C. Briens, M. Latifi, L. Ferrante, I. Berruti and D. Radlein, Effects of Temperature and Residence Time on the Thermal Cracking of Bio-oil for Syngas Production, 2009. http://dc.engconfintl.org/bioenergy_ii/33        [ Links ]

18 A.R. Mohamed, M. Mohammadi and G.N. Darzi, Preparation of carbon molecular sieve from lignocellulosic biomass: a review, Renew. Sust. Energy Rev., 2010,14, 1591-1599. DOI: 10.1016/j.rser.2010.01.024        [ Links ]

19 X. Jiang, X. Wang, X. Han and J. Tong, Effect of residence time on products yield and characteristics of shale oil and gases produced by low-temperature retorting of dachengzi oil shale, Oil Shale, 2013, 30 (4), 501-516. DOI: 10.3176/oil.2013.4.04        [ Links ]

20 J. Li and O. Talu, Effect of structural heterogeneity on multi-component adsorption: benzene and p-xylene mixture on silicate, Funda. Adsor., 1993, 80, 373-380.         [ Links ]

21 K.A.O. Santos, A.A. Dantas Neto, M.C.P.A. Moura and T.N. Castro Dantes, Separation of xylene isomers through adsorption on microporous materials: a review, Braz. J. Petrol. Gas., 2011, 5(1), 255-168. DOI: 10.5419/bjpg2011-0024        [ Links ]

 

 

Received 13 February
Revised 16 October 2018
Accepted 29 November 2018

 

 

* To whom correspondence should be addressed. E-mail: balazibya@yahoo.com

Creative Commons License All the contents of this journal, except where otherwise noted, is licensed under a Creative Commons Attribution License