SciELO - Scientific Electronic Library Online

 
vol.71Hydrazide Derivatives: An Overview of Their Inhibition Activity against Acid Corrosion of Mild SteelThe Role of Bronsted and Lewis Acidity in the Green Synthesis of Homopropargyl Alcohols over HZSM-5 índice de autoresíndice de assuntospesquisa de artigos
Home Pagelista alfabética de periódicos  

Serviços Personalizados

Artigo

Indicadores

Links relacionados

  • Em processo de indexaçãoCitado por Google
  • Em processo de indexaçãoSimilares em Google

Compartilhar


South African Journal of Chemistry

versão On-line ISSN 1996-840X
versão impressa ISSN 0379-4350

S.Afr.j.chem. (Online) vol.71  Durban  2018

http://dx.doi.org/10.17159/0379-4350/2018/v71a7 

RESEARCH ARTICLE

 

Optimization and Electrochemical Study on the Control of Mild Steel Corrosion in Hydrochloric Acid Solution with Bitter Kola Leaf Extract as Inhibitor

 

 

V.C. AnadebeI, *; O.D. OnukwuliII; M. OmotiomaIII; N.A OkaforIV

IDepartment of Chemical Engineering, Federal University Ndufu Alike Ikwo, Ebonyi State, Nigeria
IIDepartment of Chemical Engineering, Nnamdi Azikwe University Awka, Anambra state, Nigeria
IIIDepartment of Chemical Engineering, Enugu State University of Sci & Tech, Enugu State, Nigeria
IVDepartment of Chemical Engineering, Chukwuemeka Odumegwu Ojukwu University, Nigeria

 

 


ABSTRACT

Response surface methodology was applied to predict the optimum control of mild steel corrosion in acid medium with bitter kola leaf extract as inhibitor. The experiment was carried out to investigate the mutual interactions between the considered independent variables and the expected responses. Thermometric, gravimetric, potentiodynamics polarization and electrochemical impedance spectroscopy were used in the corrosion inhibition study. As a supplementary technique, infrared spectroscopy was used to analyze the pure extract and corrosion products and it was observed that some peaks shifted while some disappeared. Inhibition efficiencies of 88.24 %, 86.81 %, 90 %, 89.5 % and 85.3 % were obtained from optimization, thermometric, gravimetric, potentiodynamics polarization and electrochemical impedance spectroscopic techniques, respectively. The bitter kola leaf extract behaved as a mixed-mode inhibitor. Application of response surface methodology in this study was found to be good in predicting the optimum range for controlling of metal corrosion thereby reducing the number of experimental runs.

Keywords: Acid, bitter kola leaf, Fourier transform infrared, mild steel, electrochemical impedance spectroscopy, potentio dynamics polarization.


 

 

1. Introduction

Mild steel is a useful metal in engineering. Its usefulness is endangered by corrosion phenomenon. Corrosion is simply explained as the disintegration of metal by a reaction with its environment and is generally faster when the average atmospheric temperature is high. Some metals corrode, while many of other metals (for example, silver, gold and platinum) have strong stability in very aggressive environments such as strong acids. When metal is exposed to a natural environment, it will revert to its natural state by corroding to form compounds. In acids or other aggressive solutions attack may be rapid, while in ordinary air atmosphere the attack may be slow due to the formation of protective corrosion deposits. Metals that are not homogenous in nature or those that have rough surfaces create potential sites for the initiation of corrosion. Corrosion is responsible for numerous losses in engineering industries. To protect metallic materials, maintenance operations like pickling and cleaning are employed. Aggressive hydrochloric acid used for pickling and cleaning operations often corrodes the metallic structures. Among the various techniques of controlling corrosion, application of an inhibitor is one of the best known tech-niques.1-2 The quest for corrosion control by the application of an inhibitor is widely acceptable to maintain the stability of metallic structures.3 Organic compounds containing oxygen, nitrogen and phosphorus atoms are presumed to have strong ability to inhibit corrosion of metals in acid environments.4

Different plants extract have successfully been evaluated for their corrosion inhibiting performance. The corrosion inhibiting strength of plants extract may be attributed to their phyto-chemical constituents. It has been observed that plant extracts are of great interest, because they are cheap, biodegradable, readily available and eco-friendly.5-10 Due to their potential benefits, some plants have been examined as green inhibitors for metals in alkaline and acid environment.11-12 Among the various plant extracts, such as Thevetia peruviana extract gave 81 % efficiency for carbon steel in 1M HCl at 300 ppm,13Ocimium gratissium extract gave 82.9 % efficiency for aluminum in HCl at inhibitor concentration of 1.3 g L-1,14Chromolaena odorata and Tridax procumbens extract gave 99.8 % and 99.9 % inhibition efficiency for stainless steel in acidizing oil field environment at 400 ppm, respectively.15

This article is a continuation of previous works.5,6 RSM (response surface methodology) a statistical tool, was used for modelling and solving of the problem in which a response of interest is affected by different variables. The aim is to optimize the response (output) which is also affected by different independent variables (input). Also to systematically investigate and obtain new insight on the inhibition performance of an ethanol extract of bitter kola leaf on mild steel corrosion in the acid environment.

 

2. Experimental

2.1. Preparation of the Plant

Bitter kola leaf was collected from Uli in Anambra State of Nigeria. The leaves were sun-dried for 4 days and later ground into powder form. In the process of extraction, 30 g bitter kola leaves were weighed and immersed in 1000 mL of ethanol for 48 h followed by separation. The stock solution of the extract was subjected to phytochemical analysis to determine the presence of alkaloids, phenolics, steroids, tannins, saponins and flavo-noids. The HCl (JHD) and ethanol (JHD) used for the practical were of high grade.

2.2. Metals Preparation

Corrosion studies were performed on mild steel of compositions P (0.02 %), Mn (0.11 %), Si (0.02 %), S (0.02 %) Cu (0.01 %), C (0.23 %), Ni (0.02 %), Cr (0.01 %) and Fe (99.56 %). Prior to corrosion process, the mild steel was mechanically cut into coupons (5 cmx4cmx0.1 cm).The surface of each coupon were then polished using 800, 1200 and 220 emery papers to obtain a smooth area. The coupons were further degreased with acetone rinsed with distilled water to remove debris and dry in warm air according to previous work done.16

2.3. FTIR Analysis

Prior to the experiment, FTIR analysis was carried out on the neat sample (BKL) to identify the active functional group. Metal coupons were further introduced in the inhibited medium. After the corrosion study, the corrosion products were collected with sample bottle mixed with KBR and subjected to Fourier transform infrared spectroscopy using (SHIMADZU Model IR affin-ity-1, S/N A213747013651)to identify the functional group in the corrosion products.

2.4. Thermometric Approach

The experiment was performed using thermostat at 30 °C for the metal specimen. The temperature of the system where the mild steel was immersed was noted regularly until a stabilized temperature value was reached. The reaction number (RN) was calculated using Equation (1) as contained in other similar protocols.17-18

where Tm and Ti denote the maximum and initial temperatures in °C, t is the duration in minutes taken to reach Tm.

The inhibition efficiency was calculated by applying Equation 2 below

2.5. Gravimetric Method

Gravimetric technique was performed at temperatures of 300 K, 312 K and 324 K, respectively. As previously expressed5,6 mild steel coupons were weighed and introduced in 250 mL beakers containing 200 mL of 1.2 M HCl with inhibitor concentrations range of 0.3 gL-1,0.6gL-1, and 0.9 gL-1. The variation in the initial and final weight was studied for uninhibited and inhibited test solution. At the end of corrosion study the coupons were removed, dipped in acetone, cleaned and finally re-weighed. The experimental data were recorded. The weight loss (Aw), corrosion rate (CR), inhibition efficiency (IE) and surface coverage (0) were calculated using Equations (3), (4), (5) and (6), respectively.19

where wi and wf are initial and final weight of the coupons. wbl and winh are the weight loss values obtained in the blank and inhibited environments. A is the total area of the mild steel sample and t is the time of immersion.

2.6. Determination of Activation and Heat of Adsorption

Considering corrosion rates of the mild steel at T1 and T2 as CR1 and CR2, Equation (7) was used to predict the activation energy. The heat of adsorption Qads (kJ mol-1) was calculated using Equation (8).20

where Ea is the activation energy, R denotes gas constant, 01 and 02 represent degree of surface coverage at temperature T1 and T2. 01 and 02 were determined using Equation (6) of section 2.5

2.6.1. Adsorption Isotherms

To determine the values of the thermodynamic properties, data of concentration and surface coverage were fitted into Langmuir, Frumkin, Temkin and Flory-Huggins isotherms of Equations (9), (10), (11) and (12), respectively.

where C represent concentration of inhibitor, Kadsdenotes adsorption equilibrium, a is the lateral interaction term explaining the nature of adsorbed layer, a is the attractive parameter, x is size parameter (this is the measure of the quantity of the adsorbed water molecules sub-planted by inhibitor molecules). Then the free energy of adsorption (AGads) was evaluated using Equation (13).

2.7. Electrochemical Technique

Thorough electrochemical analysis was performed with the aid of a potentiostat/galvanostat 263 electrochemical system workstation. A graphite rod and a saturated calomel electrode (SCE) were used as reference electrodes. A mild steel specimen of 1 cm2 dimension was used as working electrode.The experiment was performed in aerated and unstirred solution at the end of 30 min of immersion, this makes the solution to reach steady state. Temperature was set at 30 ± 1 °C. Polarization studies were performed in the range ± 250 mV versus corrosion potential at a scan rate of 0.333 mV/s. The efficiency was evaluated using Equation (14).

where (bl) and (inh) are the current density values in the absence and presence of inhibitor, respectively.

2.8. Scanning Electron Microscopy

Morphological analysis of the corroded coupons were carried out at Chemical Engineering Department Ahmadu Bello University, Zaria, using the scanning electron microscope (SEM of model no MVE016477830, Manufactured by Phenom-world Eindhoven, Netherlands). The surfaces of the mild steel immersed in inhibited and uninhibited acid environments were investigated.

 

3. Results and Discussion

3.1. Spectroscopic Analysis of Bitter Kola Leaf Extract and Corrosion Product

Bitter kola leaf extract with the corrosion product formed after immersion in 1.2 M HCl solution were investigated using FTIR technique. The peak numbers in the pure extract and the extract with the corrosion products are presented in Table 1. The peak numbers indicate the functional groups of the extract as expressed by other research work,21 the stretched O-H at 3601.14 cm-1 peak of the pure extract shifted to 3547.1 cm-1 in the corrosion product. Also, stretched C-H, N-H and stretched C=C recorded changes in peaks and intensities. The change in the peaks values revealed that there was a correlation between the mild steel surface and functional groups present in the bitter kola leaf extract. The variation of the peak numbers shows that some peaks deviated, while some disappeared.22

3.2. Thermometric Results of the Corrosion Inhibition Process

Influence of inhibitor concentration (BKL) on RN and the inhibition efficiency (IE) of mild steel in HCl are presented in Table 2. Addition in concentration of the inhibitor reduces the RN, and also increased concentration enhances the inhibition efficiency.17 Maximum inhibition efficiency of 86.81 % was attained at 0.9 g L-1 of inhibitor.

 

 

3.3. Result of Gravimetric Method Using One Factor at a Time

Results of the weight loss, corrosion rate, inhibition efficiency and surface coverage of mild steel in HCl are shown in Table 3. Bitter kola leaf extract gave high inhibition efficiency (IE) which is higher than inhibition efficiencies of previously used plant extracts.5,6 The inhibition level increased with an increase in concentration of the plant extract, due to the active constituents that covers the metal surface. Similarly, the surface coverage increased by enhancing the concentration of the extract because increase in the inhibitor concentration increases the availability/ adsorption of the active components of the inhibitor onto the corroding metal surface. On the contrary, surface coverage decreased with an increased in temperature, reason being that increase in temperature tends to disperse the extract from the surface of the mild steel (breaks the heterocyclic bond of the extracts thereby reducing the surface coverage). This observation is in agreement with research work.23 Optimum inhibition efficiency of 90 % was recorded at temperature of 300 K, and 0.9gL-1 at 21 h immersion time which also implies that corrosion and inhibition process depends on time of expose with increasing the concentration of the extract molecules. It showed that bitter kola leaf extract is good for corrosion control of mild steel in HCl solution using greener approach.

 

 

3.4. Activation Energy and Heat of Adsorption Studies

Ea and Qads for the corrosion control of mild steel in HCl with bitter kola leaf extract are shown in Table 4. From the table below, calculated Ea value for the inhibited solution with bitter kola extract is 39.503 and 53.750 KJ mol-1 in the presence of inhibitor concentration of 0.6 and 0.9 gL-1while in 0.1 and 0.2 gL-1 inhibitor concentration, the activation energies are 20.525 and 25.235 KJ mol-1. The results of the activation energy prove that the electrochemical reaction of mild steel in presence of inhibitor was obstructed24 due to the heterocyclic compounds present in bitter kola extract which guide the metal surface from acid attack due to the adhesion of the film layer on the metal surface, the film layer is stronger than the degradation of the metal surface which is an exothermic reaction.25

 

 

3.4.1. The Adsorption Parameters for the Corrosion Inhibition Study

Generally, it is well known that plants extracts display their inhibitive behaviour on the steel surface through the process of adhesion. The adsorption of the inhibitor is attributed to the heterocyclic compounds in the extract thereby obstructing the invading of electrochemical reactions by forming a protective film layer which functions as a barrier, preventing the ingress of the corrodent onto the metal surface. Furthermore, in-depth knowledge of the adsorption character of an inhibitor is vital for proper understanding of the kinetics process. An adsorption isotherm explains the mutual interactions between the surface coverage of the metal with the adsorbed extract molecules and the concentration of extract molecules in acid media. Evaluation of behaviour of the adsorbent type of inhibitor can be predicted by fitting the data in the following adsorption isotherms, Langmuir, Frumkin, Temkin and Flory-Huggins isotherms. The plots are presented in Figs. 1-4) (trend line functions of Microsoft Excel was used to generate the mathematical equations). Accordingly, linear graphs were observed. It shows the relationship between the extract molecules and the coverage of the metal surface. The Langmuir isotherm has highest value of R2 (0.996), indicating strong support to Langmuir adsorption isotherm.26,27 Comparing the equations in Figs. 1-4 with the isotherm Equations 9,10,11 and 12 the adsorption properties K, a, a and x were obtained. From the Frumkin adsorption parameter, the lateral interaction term (a) gives positive values suggesting good behaviour of the inhibitor on the mild steel surface,6 from Temkin adsorption parameter, the attractive parameter value (a) is negative, showing that repulsion exists in the adsorption layer.26 The value of the size parameter (x) is positive proving that the adsorbed species of the BKL extract is bulky.20 The isotherms and the values of these parameters are presented in Table 5.

 

 

 

 

 

 

 

 

 

 

3.5. Polarization Measurements

A clear polarization curve is shown in Fig. 5. Polarization measurements were performed to evaluate the performance of BKL in obstructing the electrochemical reactions. The mild steel coupon is seen to display strong dissolution without evidence of passivation in the studied potential range in HCl solutions.28 It was equally observed that when BKL was immersed in the inhibited solution Icorr reduces compared to the uninhibited solution. Small deviation on Ecorr was noted. If the displacement in Ecorr is above 85 mV we could classify the inhibitor as anodic or cathodic and if the displacement is below 85 mV the inhibitor may be seen as a mixed-mode.29 The corresponding electrochemical parameters namely, corrosion potential (Ecorr) and corrosion current density (Icorr) were generated and their values are presented in Table 6. The maximum displacement in Ecorr value are less than 85 mV, bitter kola leaf extract behaved as a mixed-mode inhibitor.30 However, the extracts function as a mixed-mode inhibitor with predominant cathodic effect in 1.2 M HCl. These effects become more noticeable at higher concentrations. The values of the corrosion current density in the absence (Icorruninh) and presence of inhibitor (Icorrinh) were used to estimate the inhibition efficiency.

 

 

3.6. Electrochemical Impedance Spectroscopy (EIS)

Impedance spectra of mild steel in HCl solution at various concentrations of the inhibitor are shown in Fig. 6. The impedance measurements are most suitable for obtaining detailed mechanistic insights into corrosion process. The plot in each situation constitute of a single depressed capacitive semicircle in the elevated frequency area.31,32 It occurs due to coarseness of the mild steel surface.33,31The electrochemical impedance parameters of the corrosion inhibition of mild Steel in HCl solution are shown in Table 7. Due to a modification in the presence of the inhibitor, the values of Cildecreased more than the one seen in the absence of the inhibitor. Charge transfer resistance and double layer capacitance display the opposite direction, according to Helmholtz model

 

 

The change in Cdl value occurs due to a reduction in the dielectric constant and an increase in the double layer thickness can be assigned to the adhesion of inhibitor on the corroding mild steel surface.35-39 The Cdl is defined as double layer capacitance, ε-dielectric constant of the medium, eo the vacuum permittivity, A is the electrode area, δ is the thickness of the interfacial layer. Accordingly, addition of the extract in test solution gave rise in the magnitude of the Nyquist semicircle. It showed effective inhibition of the corrosion process. Increased concentration of the extracts in each case did not affect the impedance mechanism. The observed increased in Rct is due to the adhesion of a film layer on the metal surface which includes substitution of water molecules by the extract species. Rct is defined as the charge transfer resistance.

3.7. Result of Gravimetric Method using Response Surface Methodology.

Design expert version (10) software was used to design the experiment having 30 experimental runs in order to systematically have an insight on the stability of the inhibitor within the studied range and to predict the optimum range for controlling of mild steel corrosion in different test solutions as indicated in Table 8. The independent variables considered in this experiment were Acid concentration (AC), Inhibitor concentration (IC), Temperature (T), and time (t). From Table 8, it was noted that inhibition efficiency stabilizes by enhancing the inhibitor concentration of the extract molecules thereby giving the optimum range of 88.24 %. The 3-D plots for IE % of BKL extract on mild steel in HCl environment is presented in Fig. 7. The predicted versus actual inhibition efficiency plot displayed a linear graph Fig. 7A, showing that the proposed model is able to evaluate the inhibition process. The 3-D plots (Fig. 7B-D) showed the relationship between the factors influencing the corrosion process and the efficacy of BKL. The characteristics of the 3-D surfaces plot imply that there is complementary relationship among the considered factors of the corrosion process.

 

 

Fig. 7B-D depicts that increasing both time and temperature has a drastic effect on the expected response due to the increase of the environmental conditions, also enhancing the level of inhibitor promotes the inhibition process. It is known that when the average atmospheric temperature conditions are high, tendency of electrochemical reactions to occur is positive. Accordingly, the optimization overlay plot obtained conform with the experimental results, which suggest that bitter kola leaf is a potential plant extract for surface treatment of mild steel in aggressive environments.

3.8. Analysis of the Inhibition Efficiency, IE (%) as Determined using RSM

Mathematical Model of the Corrosion Inhibition Efficiency

Mathematical equations in terms of coded factors can be adopted to evaluate the response for a given levels of each factor, the big levels of the factors are coded as +1 and the small levels of the factors are coded as -1. The coded equation is vital for identifying the relative effects of the factors by comparing the factor coefficients.

Final Equation in Terms of Coded Factors

Final Equations in Terms of Actual Factors

From Table 9, the F-value of 91.55 was obtained. It demonstrates that the model is significant. There was only a 0.01 % chance that F-value obtained could occur due to noise. The noise may be assigned to flow rates of the heterocyclic compounds present in the inhibitor. Values of Prob > F lower than 0.0500 shows that model terms are pronounced. Here B, C, D, AB, BD, ΑΛ2, DA2 are pronounced model terms. Values higher than 0.1000 reveal the model terms are not pronounced. From the ANOVA table it was observed that the inhibitor concentration has the highest F-value, followed by time, temperature and acid concentration, respectively.40 The coefficient of determination R2 of the model was 0.9881 which prove a good fit between the predicted values and experimental data lines. Furthermore, the R2 explain high dependence and relationship between the observed and predicted values of the response.41 Also the 'Pre R-squared' of 0.9159 generated is in line with the Adj R-squared of 0.9776; the difference is lower than 0.2. 'Adeq precision' measures the signal to the noise ratio. A ratio higher than 4 is acceptable. The ratio of 35.019 indicates a good signal.

 

 

3.9. Scanning Electron Microscopy

The morphological analyses of mild steel are shown in Figs. 8-10). The micrograph of the mild steel revealed that corrosion holes were formed on the surface of the metal due to acid attack which indicates deposition of corrosion particles in the blank solution. Presence of inhibitor altered the rate of corrosion on the surface and a plain layer was noticed which indicates the occurrence of a protective film layer by the active constituents of the extract. This is in agreement with previous research.42-43

 

 

 

 

 

 

4. Conclusions

The obtained results indicate that BKL is a potential extract to be used for surface treatment of mild steel corrosion in HCl environment. Polarization technique signifies that BKL functioned as a mixed-mode inhibitor, which the impedance data revealed was accomplished through adsorption of BKL molecules on the metal surface. The adsorption of BKL on the metal surface conforms to physical adsorption process. Response surface methodology is the best approach for optimizing the inhibition process also reducing the number of experimental runs. Furthermore, the optical investigation revealed the occurrence of a film layer adsorbed on the metal surface, while FTIR studies revealed the functional groups existing in the adsorbed protective layer.

 

References

1 M.S. Al-Otaibi, A.M. Al-Mayouf, M. Khan, A.A. Mousa and S.A. Al-Mazroa., Corrosion inhibition action of some plants extracts on the corrosion of mild steel in acidic media, Arabian. J. Chem., 2012,1-7.         [ Links ]

2 I.B. Obot, N.O. Obi-Egbedi and S.A. Umoren., Antifungal drugs as corrosion inhibitors for aluminum in 0.1M HCl, Corros. Sci., 2009, 51(8), 1868-1875.         [ Links ]

3 O.D. Onukwuli and M. Omotioma., Optimization of the inhibition efficiency of mango extracts as corrosion inhibitor of mild steel in 1.0MH2S04usingRSM,J. Chem.Tech. Metallurgy,2016,51(3),302-314.         [ Links ]

4 A. Yildirim and M. Cetin, Synthesis and evaluation of new long alkyl side chain acetamide, isoxazolidine and isoxazoline derivatives as corrosion inhibitors, Corros. Sci., 2008, 50, 155-165.         [ Links ]

5 M. Omotioma and O.D. Onukwuli, Corrosion inhibition of mild steel in 1.0 M HCl with castor oil extract as inhibitor, Int. J. Chem. Sci., 2016a, 14(1) 103-127.         [ Links ]

6 M. Omotioma and O.D. Onukwuli, Modeling the corrosion inhibition of mild steel in HCl medium with the inhibitor of paw-paw leaves extract, Port. Electrochim. Acta, 2016b, 34(4), 287-294.         [ Links ]

7 P. Bommersbach, C. Alemany-Dumont, J.P. Millet and B. Normand, Formation and behavior study of an environment-friendly corrosion inhibition by electrochemical methods, Electrochim. Acta., 2005,51(6), 1076-1084.         [ Links ]

8 K. Radojcic, S. Berkovic, J. Kovac, Vorkapic-Furac, Natural honey and black radish juice as tin corrosion inhibitors, Corros. Sci., 2008, 50(5), 1498-1504.         [ Links ]

9 P.C. Okafor, M. Ikpi, E.I. Uwah, E.E. Ebenso, U.J. Ekpe and S.A. Umoren, Inhibitory action of Phyllanthus amarus extracts on the corrosion of mild steel in acidic media, Corros. Sci., 2008, 50(8), 2310-23177.         [ Links ]

10 M. Salasi, T. Sharabi. E. Roayaei and Aliofkharaei, The electrochemical behavior of environment-friendly inhibitors of silicate and phosphonate in corrosion control of carbon steel in soft water media, Mater. Chem. Phys, 2007,104, 183-190.         [ Links ]

11 E.E. Ebenso and U.J. Ekpe, Kinetic study of corrosion inhibition of mild steel in H2SO4 using carica papaya leaves extract, West. Afr. J. Bio. App. Chem, 1996,41, 21-27.         [ Links ]

12 M. Abdel-Gaber, B.A. Abd-El-Nabey, I.M. Sidahmed, A.M. El-Zayaday and M. Saa, Inhibitive action of some plants extracts on the corrosion of steel in acidic media, Corros. Sci.,,2006,48,2765-2779.         [ Links ]

13 A.S. Fouda, E.H. Megahed, N. Fouda and N.M. Elbahrawt, Corrosion inhibition of carbon steel in 1.M hydrochloric acid solution by aqueous extract of Thevetia peruviana, J. Bio Tribo Corros., 2016, 2, 1-16.         [ Links ]

14 D.I. Udunwa, O.D. Onukwuli and M. Omotioma, Corrosion control of aluminum alloy in HCl medium usingextract of Ocimum gratissium as inhibitor, Der Pharma Chemica, 2017, 9(19) 48-59.         [ Links ]

15 S. Aribo, J.O. Sunday, J.I. Leonard, O. Akinlabi and O.F. Davies, Green inhibitors for corrosion protection in acidizing oilfield environment, J. Association. Arab. Uni. Basic Appl. Sci., 2017, 24, 34-38.         [ Links ]

16 A.A Khadom, A.F. Hassan, B.M. Abod, Evaluation of environmentally friendly inhibitor for galvanic corrosion of steel-copper couple in petroleum waste water, Process Safety. Env. Protection.,2015,98,93-101.         [ Links ]

17 E.M. Mabrouk, H. Shorkry, K.M. and Abu Al-Naja, Inhibition of aluminum corrosion in acid solution by mono- and bis-azo naphthy lamine dyes. Part 1, Chem. Met. Alloys, 2011,4, 98-160.         [ Links ]

18 N.O. Eddy, B.I Ita, S.N. Dodo and E.D. Paul, Inhibitive and adsorption properties of ethanol extract of Hisbisais sabdariffa calyx for the corrosion of mild steel in 0.1 M HCl, Green Chem. Lett. Rev., 2012,5(1), 43-53.         [ Links ]

19 N. Nagm, N.G. Kandile, E.A. Badr and M.A. Mohammed, Gravimetric and electrochemical evolution of environmentally friendly nonionic corrosion inhibitors for carbon steel in 1M HCl, Corros. Sci., 2012, 65, 94-103.         [ Links ]

20 J.T. Nwabanne and V.N. Okafor, Inhibition of the corrosion of mild steel in acidic medium by Vernonia amygdalina: adsorption and themodynamic study, J. Emerging Trends Eng. Appl. Sci. (JETEAS)., 2011, 2(4), 619-625.         [ Links ]

21 V.C. Anadebe, N.A. Okafor, B.O. Okafor and C.C. Emmanuel, Spectroscopic analysis of Garcina kola leaf extract, World News Nat. Sci., 2017, 15, 162-168.         [ Links ]

22 A.C. Maduabuchi, S. Nwanonenyi, D. Njoku, B.I. Nkem, E.E. Oguzie and Li. Ying, Experimental study on the inhibitive effect of phytic acid as a corrosion inhibitor for Q235 mild steel in 1M HCl environment, World News Nat. Sci., 2017,15, 1-19.         [ Links ]

23 M. Abulwahab, A. Kasim, K.A. Bello and J.O. Gaminana, Corrosion inhibition of multi component aluminum alloy in HCl acid solution by aqueous extract of bitter leaf (Vermina amygdalina) powder. Adv. Mater. Res., 2012, 367, 319-325.         [ Links ]

24 A.A. Khadom, N.A. Ahmed and A.A. Nagham, Xanthium strumarium leaves extracts as a friendly corrosion inhibitor of low carbon steel in HCl: kinetics and mathematical studies, S. Afr. J. Chem. Eng., 2017,25, 13-21.         [ Links ]

25 A.K. Satapathy, G. Gunasekaran, Kumar Amit and P.V. Rodrigues, Corrosion inhibition by justice gendarussa plant extract in hydrochloric acid solution, Corros. Sci., 2009, 51, 1317-1325.         [ Links ]

26 L.A Nnanna, I.O. Owate, O.C. Nwadiuko, N.D. Ekekwe and W.J. Oji, Adsorption and corrosion inhibition of gentum Aficana leaves extract on carbon steel. Int. J. Mater. Chem, 2103, 3(1), 10-16.         [ Links ]

27 V.G. Vasudha and P.K. Shanmuga, Polyalthia longitolia as a corrosion inhibitor for mild steel in HCl solution, Res. J. Chem. Sci., 2013, 3(1), 21-26.         [ Links ]

28 E.E. Oguzie, Z.O. Ihebunike, K.L Oguzie, C.E. Ogukwe, M.A. Chidiebere, C. Enenebeaku and C.O Akaelzi, Corrosion inhibiting effect of Aframomum melegueta extracts and adsorption characteristics of the active constituents on mild steel in acidic media, J. Disp. Sci. Tech., 2013, 34, 516-527.         [ Links ]

29 M.A. Chidebere, L. Nnanna, A.C. Blessing, K. Oguzie, O. Beluonwu, O. Benedict and E.E. Oguzie, Inhibition of acid corrosion of mild steel using Deonix regia leaves extract, Int. Lett. Chem. Phys. Astron., 2016,69, 74-86.         [ Links ]

30 E.E. Oguzie, C.K. Enenebeaku, C.O Akalezi, S.C. Okoro, A.A. Ayuk and E.N. Ejike, Adsorption and corrosion inhibiting effect of Dacry-odis edulis extract on low carbon steel corrosion in acidic media, J. Colloid. Int. Sci., 2010, 349, 283-292.         [ Links ]

31 A. Popova, E. Sokolova, S. Raicheva and M. Christov, AC and DC study of the temperature effect on mild steel corrosion in acid media in the presence of benzimidazole derivatives, Corros. Sci., 2003, 45, 33-58.         [ Links ]

32 H. Ashassi-Sorkhabi, D. Seifzadeh and M.G Hosseini, EN, EIS and polarization studies to evaluate the inhibition effect of 3H-pheno-thiazi in -3-one, 7-dimethylamin on mild steel corrosion in 1M HCl solution, Corros. Sci., 2008, 50, 3363-3370.         [ Links ]

33 F.S. De Souza and A. Spinelli, Caffeic acid as a green corrosion inhibitor for mild steel, Corros. Sci., 2009, 51, 642-649.         [ Links ]

34 L.G. Da Trindade and R.S. Goncalves, Evidence of caffeine adsorption on low carbon steel surface in ethanol, Corros. Sci., 2009, 51, 1543-1578.         [ Links ]

35 J.C. Da Rocha, Da. Cunha Poniciano Gomes and E. D'Elia, Corrosion inhibition of carbon steel in HCl solution by fruit peel aqueous extract, Corros. Sci., 2010, 52, 2341-2348.         [ Links ]

36 M. Lebrini, F. Robert, A. Lecante and C. Roos, Corrosion inhibition of C38 steel in IM HCl acid medium by alkaloids extract from Oxandra asbecki plant, Corros. Sci., 2010, 53, (2) 687-695.         [ Links ]

37 M.A. Chidiebere, E.E. Oguzie, L. Liu, Y. Li and F. Wang, Corrosion inhibition of Q235 mild steel in 0.5 M H2SO4 solution by phytic acid and synergistic iodide additives, Ind. Eng. Chem. Res., 2014,53,7670-7679.         [ Links ]

38 M.A. Chidiebere, C.E. Ogukwe, K.L. Oguzie, C.N. Eneh and E.E. Oguzie, Corrosion inhibition and adsorption behavior of Punica granatum extract on mild steel in acidic environments: experimental and theoretical studies, Ind. Eng. Chem. Res., 2012, 51, 668-677.         [ Links ]

39 M.A. Chidiebere, E.E. Oguzie, L. Liu, L. Yingand F. Wang, Adsorption and corrosion inhibiting effect of riboflavin on Q235 mild steel corrosion in acidic environments, Mater. Chem. Phys., 2015,156, 95-104.         [ Links ]

40 D. Bas and I.H. Bayaci, Modeling and optimization I: usability of response surface methodology, J. Food. Eng., 2007, 78, 836-845.         [ Links ]

41 P. Sharma, L. Singh and N. Dilbaghi, Optimization of green variables for decolorization of disperse yellow 211 by Bascillus subtiles using Box-Behnken design, J. Hazard. Mater., 2009,164, 1024-1029.         [ Links ]

42 K.K. Alaneme, Y.S. Daramola, S.J. Olusegun and A.S Afolabi, Corrosion inhibition and adsorption characteristics of rice husk extracts on mild steel immersed in 1M H2SO4 and HCl solutions. Int. J. Electrochem. Sci., 2015, 50, 3553-3567.         [ Links ]

43 K.H. Hassan, A.A. Khadom and N.H. Kurshed, Citrus aurantium leaves extract as a sustainable corrosion inhibitor of mild steel in sulfuric acid. S. Afr. J. Chem. Eng., 2016, 22, 1-5.         [ Links ]

 

 

Received 25 January 2018
Revised 24 May 2018
Accepted 25 May 2018

 

 

* To whom correspondence should be addressed. E-mail: anadebechika@gmail.com

Creative Commons License Todo o conteúdo deste periódico, exceto onde está identificado, está licenciado sob uma Licença Creative Commons