SciELO - Scientific Electronic Library Online

vol.111 número3The influence of Mn on the tensile properties of SSM-HPDC Al-Cu-Mg-Ag alloy A201Solidification of an Al-Zn alloy during semi-solid processing índice de autoresíndice de assuntospesquisa de artigos
Home Pagelista alfabética de periódicos  

Serviços Personalizados



Links relacionados

  • Em processo de indexaçãoCitado por Google
  • Em processo de indexaçãoSimilares em Google


Journal of the Southern African Institute of Mining and Metallurgy

versão On-line ISSN 2411-9717
versão impressa ISSN 0038-223X

J. S. Afr. Inst. Min. Metall. vol.111 no.3 Johannesburg  2011




Nitriding of ilmenite and high-grade slag fines



D.S. van Vuuren; G.T. Tshilombo

Materials Science and Manufacturing, CSIR




Titanium bearing resources can selectively be chlorinated at temperatures below 200ºC if the TiO2in the feed is nitrided before chlorination. However, the nitriding reaction is highly endothermic, requires highly reducing conditions, is only thermodynamically favourable at elevated temperatures, and is affected by mass and heat transfer restrictions. At the required processing conditions, problems might also be experienced with sintering and with melting of slag forming components in the raw materials.
A test programme was undertaken to study the effects of raw material type, temperature, gas composition, bed depth, carbon to raw material ratio and residence time in order to simulate conditions required for scaling up a nitriding process.
In contrast to previous experience with low-grade titaniumbearing slag containing about 30% TiO2, ilmenite and chlorinateable slag do not form melting phases under the studied nitriding conditions and hardly sintered at all. Both feed materials can readily be nitrided with conversions in excess of 90% at temperatures around 1300ºC and using bituminous coal as reducing agent with fixed carbon in excess of 1.1 times the stoichiometric requirement. The conversion decreases as the bed depth of the feed material increases and the N2/CO ratio in the gas decreases.
Analysis of the relative rates of mass and heat transfer into the reacting beds of ilmenite and slag showed that the heat transfer rates are more limiting than the mass transfer rates. In order to increase the throughput that can be achieved in a kiln, it would be necessary to take special measures to enhance the heat transfer rates into the mass of reacting material. One such a measure is to pre-form the mass of reacting material into thin-walled, hollow brick shapes prior to introducing it into a kiln.
Depending on bed depth, temperature and N2/CO ratio, required residence times in the high temperature zone of the kiln can vary between about 6 and 10 hours.

Keywords: Titanium dioxide, titanium nitride, carbo-thermic, reduction, ilmenite, slag, tunnel kiln, residence time



“Full text available only in PDF format”




1. MOSTERT, G.J., ROHRMANN, B.R., WEDLAKE, R.J., and BAXTER, R.C. Process for the recovery of titanium values, US Patent 5,224,986, 6 July 1993.         [ Links ]

2. VAN VUUREN, D.S. and STONE, A.K. Selective recovery of titanium dioxide from low grade sources, South African Chemical Engineering Congress, Durban, 20-22 September 2006.         [ Links ]

3. ADIPURI, A., ZHANG, G., and OSTROVSKI, O. Chlorination of titanium oxycarbonitride produced by carbothermal nitridation of rutile, Ind. Eng. Chem. Res., vol. 48, 2009, pp. 779-787.         [ Links ]

4. VAN VUUREN, D.S., MORRISON, A.M., and STONE, A.K. Endothermic reaction of solids loaded on trolleys moving in a kiln, US Patent 6,629,838, 7 October. 2003.         [ Links ]

5. GUEGIN, M. and CARDARELLI, F. Chemistry and mineralogy of titania-rich slags. Part 1-Hemo-ilmenite, sulphate and upgraded titania slags, Mineral Processing and Extractive Metall. Rev. 2007, vol. 28, p. 1.         [ Links ]

6. OUTOKUMPU RESEARCH OY, HSC Chemistry 6.1, Chemical Reaction and Equilibrium Software with Thermochemical Database and Simulation Module, ISBN 978-952-9507-12-2.         [ Links ]

7. SATTERFIELD, C.N. Mass Transfer in heterogeneous catalysis, Robert E. Krieger Publishing Co., 1981, p. 36.         [ Links ]

8. PISTORIUS, P.C. Kinetics of carbothermic reduction reactions under heat transfer control: modelling results, Scan. J of Metall, vol. 34, 2005, p. 122.         [ Links ]

9. SIH, S.S. and BARLOW, J. Measurement and prediction of the thermal conductivity of powders at high temperatures, Proceedings of the Solid Freeform Fabrication Symposium 1994, University of Texas, Austin, Texas, USA, p. 321.         [ Links ]

10. COETSEE, T. and PISTORIUS, P.C. Measurement of reduction in a packed bed of iron and carbon under one-dimensional heating, Ironmaking and Steelmaking, vol. 36, 2009, p. 402.         [ Links ]

11. SHEI˘NDLIN, A.E. Ed. Emissive Properties of Solid Materials: Handbook, (Énergiya, Moscow, 1974) quoted by Zolotarev, O.O., High-temperature spectral emissivity of SiC in the IR range, Optics and Spectroscopy, 2007, 103, p. 592.         [ Links ]

12. SIH, S.S. and BARLOW, J.W. Emissivity of powder beds, In: Marcus H.L. et al. (eds.). Solid freeform fabrication symposium proceedings, Austin (Texas, USA). Kluwer, Boston, 1995, p. 402.         [ Links ]

Creative Commons License Todo o conteúdo deste periódico, exceto onde está identificado, está licenciado sob uma Licença Creative Commons