SciELO - Scientific Electronic Library Online

 
vol.111 número3Titanium production via metallothermic reduction of TiCl4in molten salt: Problems and productsMicrostructure evolution in Ti-6Al-4V alloy during hydrogen dosing at elevated temperature índice de autoresíndice de assuntospesquisa de artigos
Home Pagelista alfabética de periódicos  

Serviços Personalizados

Artigo

Indicadores

Links relacionados

  • Em processo de indexaçãoCitado por Google
  • Em processo de indexaçãoSimilares em Google

Compartilhar


Journal of the Southern African Institute of Mining and Metallurgy

versão On-line ISSN 2411-9717

J. S. Afr. Inst. Min. Metall. vol.111 no.3 Johannesburg  2011

 

TRANSACTION PAPER

 

Effect of process control agent (PCA) on the characteristics of mechanically alloyed Ti-Mg powders

 

 

C. Machio; H.K. Chikwanda; S. Chikosha

Council for Scientific and Industrial Research (CSIR)

 

 


SYNOPSIS

This paper reports the results of a study to determine the effect of process control agent (PCA) on the characteristics of Ti-Mg powders during milling. It has been shown that a 2% increase in PCA content leads to up to a 40% increase in yield of the milled powder but reduces the kinetics of the mechanical alloying process. The introduction of 4% PCA decreases the mean powder particle size by up to 30%, whereas 6% PCA increases the mean particle size by up to 230%. The characteristics of the milled powders will be discussed in relation to the role of PCA in the milling process.

Keywords: Titanium-magnesium, mechanical alloying, PCA


 

 

“Full text available only in PDF format”

 

 

References

1. EKVALL, J.C.J., RHODES, E., and WALD, G.G. (eds.), Design of fatigue and fracture resistant structures, ASTM Special Publication 761, ASTM, Philadelphia, 1982, pp. 328-336.         [ Links ]

2. SURYANARAYANA, C. Mechanical alloying and milling. Progress in Materials Science, 2001, 1, 46(1-2), pp. 1-184.         [ Links ]

3. SUN, F. and FROES, F.H. (Sam). Synthesis and characterization of mechanical-alloyed Ti-xMg alloys. J Alloys Compounds, 2002 6/26,340 (1-2), 220-5.         [ Links ]

4. MACHIO, C., NYABADZA, D., CHIKWANDA, H.K,. PHASHA, M., and SIBANDA, V.M. Mechanical alloying and sintering of Ti - 10 Wt.% Mg powders. Materials Science Forum, 2009, 618 619, 105-8.         [ Links ]

5. LU, L. and ZHANG, Y.F. Influence of process control agent on interdiffusion between Al and Mg during mechanical alloying. J Alloys Compounds, 1999, 8/30, 290(1-2), 279-83.         [ Links ]

6. HWANG, S., NISHIMURA, C., and MCCORMICK, P.G. Mechanical milling of magnesium powder. Materials Science and Engineering A, 2001, 11, 318(1-2), 22-33.         [ Links ]

7. GUITTOUM, A., LAYADI, A., BOURZAMI, A., TAFAT, H., SOUAMI, N., BOUTARFAIA, S., and LACOUR, D. X-ray diffraction, microstructure, mössbauer and magnetization studies of nanostructured Fe50Ni50 alloy prepared by mechanical alloying. J Magn Magn Mater, 2008, 320, (7), 1385-92.         [ Links ]

8. LU, L., LAI, M.O., and FROYEN, L. Effects of mechanical milling on the properties of mg-10.3% ti and mg-5% al-10.3% Ti metal-metal composite. J Alloys Compd, 2005, 387, (1-2), 260-4.         [ Links ]

Creative Commons License All the contents of this journal, except where otherwise noted, is licensed under a Creative Commons Attribution License