SciELO - Scientific Electronic Library Online

 
vol.109 issue4Surface drainage around the Venetia pitA critical comparison between a compressed air driven rocker arm shovel and a track-bound non-throw loader author indexsubject indexarticles search
Home Pagealphabetic serial listing  

Journal of the Southern African Institute of Mining and Metallurgy

On-line version ISSN 2411-9717
Print version ISSN 0038-223X

J. S. Afr. Inst. Min. Metall. vol.109 n.4 Johannesburg Apr. 2009

 

JOURNAL PAPER

 

Investigation of factors influencing the attrition breakage of coal

 

 

V. Oberholzer; J. van der Walt

School of Chemical and Minerals Engineering, North West University

 

 


SYNOPSIS

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal's breakage mechanisms, which could lead to the ability to predict the generation of fines.
The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage.
Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.


 

 

“Full text available only in PDF format”

 

 

References

AUSTIN, L., KLIMPEL, R., and LUCKIE, P. Process engineering of size reduction: Ball milling. New Yersey: Guinn Printing. 1984.         [ Links ]

CIMADEVILLA, J., ALVAREZ, R., and PIS, J. Influence of coal forced oxidation on technological properties of cokes produced at laboratory scale. Fuel processing technology, 2005, pp. 1-10.         [ Links ]

ESTERLE, J., KOLATSCHEK, Y., and O'BRIEN, G. Relationship between in situ coal stratigraphy and particle size and composition after breakage in bituminous coals. International Journal of Coal Geology, vol. 49, 2002. pp. 195-214.         [ Links ]

FALCON, L. and FALCON, R. The application of coal petrography to certain benficiation techniques on South African coal. Spec. Publ.geol.Soc.S.Afr, vol. 7, 1983. pp. 137-148.         [ Links ]

FALCON, L. and FALCON, R. The petrographic composition of Southern African coals in relation to friability, hardness, and abrasive indices. Journal of the South African Institute of Mining and Metallurgy, vol. 87 no. 10, 1987. pp. 323-336.         [ Links ]

FALCON, R. and HAM, A. The characteristics of Southern African coals. Journal of the South African Institute of Mining and Metallurgy, vol. 88 no. 5, 1988. pp. 145-161.         [ Links ]

GOVENDER, A. AND VAN DYK, J. Effect of wet screening on particle size distribution and coal properties. Fuel, vol. 82, 2003. pp. 2231-2237.         [ Links ]

HOGG, R. Breakage mechanisms and mill performance in ultra fine grinding. Powder Technology, vol. 105, 1999. pp. 135-140.         [ Links ]

HORSFALL, D. Coal Preparation and Usage. Coal Publications (Pty) Ltd. 1993.         [ Links ]

KELLY, E.G. and SPOTTISWOOD, D.J. Introduction to mineral processing. John Wiley & Sons. 1989.         [ Links ]

LE ROUX, M., CAMPBELL, Q., WATERMEYER, M., and DE OLIVEIRA, S. The optimization of an improved method of fine coal dewatering. Minerals Engineering, vol. 18, 2005. pp. 931-934.         [ Links ]

MACGREGOR, I. Preliminary investigation of predictors of the cutting forces for some South African coals. Journal of South African Institute of Mining and Metallurgy, vol. 85, no. 8, 1985. pp. 259-279.         [ Links ]

OSBORNE, D. Coal preperation technology. London: Graham & Trotman. vol. 2, 1988.         [ Links ]

RUBIERA, F., ARENILLAS, A., FUENTE, E., MILES, N., and PIS, J. Effect of the grinding behaviour of coal blends on coal utilisation for combustion. Powder Technology, vol. 105, 1999. pp. 351-356.         [ Links ]

SAHOO, R. Degradation characteristics of steel making materials during handling. Powder Technology, vol. 176, 2007. pp. 77-87.         [ Links ]

SAHOO, R. and ROACH, D. Quantification of lump coal breakage during handling operation at the Gladstone port. Chemical Engineering and Processing, vol. 44, 2005. pp. 797-804.         [ Links ]

VAN DYK, J., KEYSER, M., and VAN ZYL, J. Suitability of feedstock for the Sasol-Lurgi fixed bed by bottom gasification process. Gasification Technologies 2001. California: Sasol Technologies, R&D Division. 2001.         [ Links ]

WIESE, Y. and LOUW, E. Factors influencing attrition breakage of coal. Northwest University, School for Chemical and Minerals Engineering. Potchefstroom: Y. Wiese. 2007.         [ Links ]

 

 

Paper written on project work carried out in partial fulfilment of B.Ing. (Chem. Eng.)

Creative Commons License All the contents of this journal, except where otherwise noted, is licensed under a Creative Commons Attribution License