SciELO - Scientific Electronic Library Online

 
vol.109 issue2Incorporation of rehabilitation cost into the optimum cut-off grade determinationCFB technology provides solutions for reducing CO2 emissions author indexsubject indexarticles search
Home Pagealphabetic serial listing  

Journal of the Southern African Institute of Mining and Metallurgy

On-line version ISSN 2411-9717

J. S. Afr. Inst. Min. Metall. vol.109 n.2 Johannesburg Feb. 2009

 

TRANSACTION PAPER

 

Rock bolt condition monitoring using ultrasonic guided waves

 

 

B.J. BuysI; P. S. HeynsI; P.W. LovedayII

IDynamic Systems Group, Department of Mechanical and Aeronautical Engineering, University of Pretoria
IISensor Science and Technology, Material Science and Manufacturing, CSIR

 

 


SYNOPSIS

Rock bolt integrity is a critical issue for the mining industry because of its influence on the safety of mining operations. Guided ultrasonic wave testing of the defects associated with resinanchored rock bolts was investigated. Axisymmetrical and threedimensional finite element models were built, one of a partially encapsulated bolt and the other of a bolt with a simulated local corrosion crack. Experimental bolts were then installed in a testing block and typical responses were compared to finite element models of different defect scenarios.
Encouraging results were obtained for the smaller axisymmetrical and three-dimensional finite element models, as well as during the experimental investigation. It is recommended that software with energy-absorbing elements should be utilized to consider higher frequencies and longer bolts. Once the integrity of models such as these has been established, the models could in principle be used to train neural networks for use in commercial equipment to determine the integrity of the installed bolt.


 

 

“Full text available only in PDF format”

 

 

References

1. SOUTH AFRICAN DEPARTMENT OF MINERALS AND ENERGY-Mine Health and Safety Inspectorate. Annual Report 2006-2007. http://www.dme.gov.za/mhs/documents.stm#3, Accessed 2008-10-12.         [ Links ]

2. ROBERTS, D.P. Testing of mining tunnel support elements and systems for hard rock mines. Master's dissertation. Natal: University of Natal. 1995.         [ Links ]

3. BORNMAN, H. of Duraset, a South African rock bolt supplier. South African rock bolts consumption. Unpublished e-mail to Buys B.J. (25 April 2005).         [ Links ]

4. MARK, C., COMPTON, C.S., OYLER, D.C. and DOLINAR, D.R. Anchorage pull testing for fully grouted roof bolts. Proceedings, 21st International Ground Control in Mining Conference, Morgantown, WV, August 6-8, 2002, pp. 105-113.         [ Links ]

5. KELLY, A.M. and JAGER, A.J. Critically evaluate techniques for the in situ testing of steel tendon grouting effectiveness as a basis for reducing fall of ground injuries and fatalities. Report submitted to SIMRAC, Report No. GAP205, October 1996.         [ Links ]

6. HARPER, G.S. and BASSON, E. Develop a new methodology of determining the effectiveness of grouted support. Report submitted to SIMRAC, Report No. GAP412, January 1998.         [ Links ]

7. STARKEY, A., IVANOVIC, A., NEILSON, R. and RODGER, A. Using a lumped parameter dynamic model of a rock bolt to produce training data for a neural network for diagnosis of real data. Meccanica, vol. 38, 2003, pp. 131-142.         [ Links ]

8. THURNER, H.F. Rock bolting-Reference bank, AMFO 84-0847 Final Report. Translated from the Swedish by BC Baur and Associates, Courtesy of CSIR. Johannesburg (Appendix of Kelly A.M., Jager A.J.), Critically evaluate techniques for the in situ testing of steel tendon grouting effectiveness as a basis for reducing fall of ground injuries and fatalities, 1996.         [ Links ]

9. BEARD, M.D. and LOWE, M.J.S. Non-destructive testing of rock bolts using guided ultrasonic waves. International Journal of Rock Mechanics & Mining Sciences, vol. 40, 2003, pp. 527-536.         [ Links ]

10. ROSE, J.L. Ultrasonic waves in solid media. Cambridge. Cambridge University Press, 1999.         [ Links ]

11. CLIFFORD, B. Ultrasonics for integrity testing of rockbolts in mines. Contract Research Report No. 3792/R31.069 prepared by Rock Mechanics Technology Ltd for the Health and Safety Executive, 2000.         [ Links ]

12. SECO, F., MARTÍN, J.M., JIMÉNEZ, A., PONS, J.L., CALDERÓN, L. and CERES, R. PCdisp: A tool for the simulation of wave propagation in cylindrical waveguides. 9th International Congress on Sound and Vibration. Orlando, Florida, 2002.         [ Links ]

13. MOSER, F., JACOBS, L.J. and QU, J. Modeling elastic wave propagation in waveguides with the finite element method. NDT&E International, 1999, vol. 32, pp. 225-234.         [ Links ]

14. ROSS, M. Modeling methods for silent boundaries in infinite media. Fluidstructure interaction aerospace engineering sciences. University of Colorado at Boulder, 2004.         [ Links ]

15. STASZEWSKI, W.J., BOLLER, C. and TOMLINSON, G.R. Health monitoring of aerospace structures. John Wiley & Sons, Chichester, UK, 2004.         [ Links ]

Creative Commons License All the contents of this journal, except where otherwise noted, is licensed under a Creative Commons Attribution License